Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Blog Article
They are making a few good points on How to Install a Bathtub in general in this article just below.
Setting up a tub isn't exactly brain surgery, but it does need solid plumbing, woodworking, and in some cases, tiling abilities. Changing an old bath tub with a brand-new one is also a reasonably challenging job. If the old tub is readily available, the project can move immediately; if you have to open up a wall surface to eliminate the old tub as well as position the brand-new bath tub, the job is a lot harder. In either instance, the job is within a residence handyman's abilities, although you will certainly require a helper to move out the old tub and embeded in the new one. Make certain you have actually qualified yourself for the work and are comfortable attempting it. Rather than hiring a specialist to take over a halfway-completed project, it is better to consider utilizing one before you begin. Possibilities are you may require an expert plumber to make tube links.
This short article will help you set up a new bathtub in your bathroom if you have currently acquired a new tub and also don't require to change the plan of your previous water supply pipelines.
Your tools and also product checklist must comprise the following:
Preparing for the Setup
To start with, the supporting frame provided with the bath needs to be fitted (if required) according to the maker's directions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is necessary to make certain that if the tap includes a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the faucets unit to avoid stress on the bathtub.
Fit the versatile tap connectors to the bottom of both faucets making use of 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you make use of all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its last position.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is detach the water supply. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The procedure of removing the existing taps can be quite problematic because of the restricted accessibility that is typically the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the remaining water that will come from the pipelines. As soon as the supply pipes have actually been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from turning during this procedure. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any old securing compound.
Before going on to fit the new faucets, compare the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Installing the Bath tub
Using the two wooden boards under its feet, put the bath tub in the called for setting. The wood boards are handy in evenly spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 tiny points.
The following goal is to guarantee that the tub is leveled all round. This can be attained by inspecting the level as well as changing the feet on the bathtub up until the spirit level reviews level.
To set up faucets, fit all-time low of the outermost versatile faucet connector to the suitable supply pipe by making a compression join; after that do the exact same for the other tap.
Switch on the water system as well as check all joints and new pipework for leakages and tighten them if required. Fill the bathtub and additionally inspect the overflow outlet as well as the regular electrical outlet for leaks.
Ultimately, deal with the bathroom paneling as explained in the maker's user's manual. Tiling and sealing around the bath tub should wait till the tub has actually been utilized a minimum of once as this will certainly resolve it into its final position.
Suitable New Touches
If the tails of the new faucets are plastic, then you will need a plastic port to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end gives a connection to the existent supply pipes.
If you require to fit a monobloc, then you will need minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the placing opening in the bath/basin guaranteeing that the washers are in location between the faucet and the sink. Secure the faucet in position with the manufacturer given backnut. When the faucet is firmly in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular tap adapters. The former type needs to be attached to the faucet finishes first, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath meets the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to split a rigid seal, causing the water to penetrate the wall in between the bath as well as the tiling, leading to problems with dampness and also possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your fixtures and fittings. They are sold in tubes as well as cartridges, as well as can securing gaps approximately a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of soaked newspaper or soft rope. Remember to always fill up the bathtub with water before sealing, to enable the motion experienced when the tub is in usage. The sealant can crack rather very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also conveniently available on the market. It is a good idea to fit the tiles making use of waterproof or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading up on Tools You Need to Install a New Bathtub ? Leave feedback directly below. We will be delighted to find out your suggestions about this content. Hoping that you visit us again in the future. In case you appreciated our blog post plz make sure you remember to pass it around. Thank you for taking the time to read it.
Plumbing emergency? We're ready. Report this page